burnt_fingers Posted January 6, 2010 Share Posted January 6, 2010 I recently bought a box of glue dots designed for adhering wick tabs. The problem is after pouring in the wax the dot looses it hold and the wick tab moves about in the container. I always clean glass containers with Dawn dishwashing liquid followed by a vinegar and hot water rinse to ensure any oily residue is removed. Anyone else have this problem? Solution? Quote Link to comment Share on other sites More sharing options...
Stella1952 Posted January 6, 2010 Share Posted January 6, 2010 Yep, that's why I don't use 'em. I use Permatex High-Temp silicone gasket maker (from AutoZone). Lesser adhesives are fine for testing, but products for others need to be well-stuck.There is much previous discussion about this and different solutions if you search. Quote Link to comment Share on other sites More sharing options...
burnt_fingers Posted January 6, 2010 Author Share Posted January 6, 2010 Good thing the glue dots were cheap on ebay. How long does it take the silicon to dry before pouring in the wax? Quote Link to comment Share on other sites More sharing options...
burnt_fingers Posted January 6, 2010 Author Share Posted January 6, 2010 I see from doing a search that it approximately 24 hours for the silicon to cure. So it looks like setup on day and pour the next. Quote Link to comment Share on other sites More sharing options...
*Dee* Posted January 6, 2010 Share Posted January 6, 2010 walmart has the permatex in their auto dept too. it will usually dry in an hour or so. but some people let them sit for a few hours or more. but once i can lift the whole jar with the wick i think its set up enough lol Quote Link to comment Share on other sites More sharing options...
LuminousBoutique Posted January 7, 2010 Share Posted January 7, 2010 for home use/testing hot glue works well too Quote Link to comment Share on other sites More sharing options...
Stella1952 Posted January 7, 2010 Share Posted January 7, 2010 I like the red Permatex, BUT for testing, I use hot glue or stickies 'cause the Permatex is a B*TCH to remove... Haven't tried the 3M ones yet that Steve was kind enough to post a photo of in the following link... He gave a strong recommendation for these so I'm gonna give 'em a try. If they work as well as the silicone glues, I wouldn't mind leaving behind the tubes of sticky ooze and waiting several hours before being able to pour!http://www.craftserver.com/forums/showthread.php?t=87159&highlight=Permatex&page=3Using "permatex" as a keyword & searching this forum, I found...Another "wandering wick" discussion...http://www.craftserver.com/forums/showthread.php?t=87159MANY different methods are discussed in that topic... The search tool is a wonderful thing. Quote Link to comment Share on other sites More sharing options...
burnt_fingers Posted January 7, 2010 Author Share Posted January 7, 2010 (edited) I think I'll look for some of those 3M adhesive sheets. I like the idea of not having to wait a few hours or more for the silicon to cure before pouring.Thanks Stella1952 for the link. Edited January 7, 2010 by burnt_fingers Quote Link to comment Share on other sites More sharing options...
topofmurrayhill Posted January 7, 2010 Share Posted January 7, 2010 The 3M mounting foam is exactly the same thing as wick stickums, just in the form of a strip instead of discs. Unlike the variable-quality stickums you get from candle suppliers, the 3M product is always reliable. The only disadvantage I can think of is if you don't like square versus round pieces.I mentioned the 3M stuff earlier in the same thread that Stella referenced, as well as several others over the past 3 years or so. In all this time using it for testers, I've never had it come loose.The fact that silicone is basically permanent (can only be removed by physical force) is both an advantage and a disadvantage, depending on what you're using it for. And you do have to place your wicks the day before, to give it time to harden and stop outgassing. That makes silicone a poor option for testers.For candlemaking purposes, it doesn't matter whether you use the GE or the Permatex. The results are identical. Quote Link to comment Share on other sites More sharing options...
Gypsyjen Posted January 7, 2010 Share Posted January 7, 2010 I don't use the permanent adhesives because I would like to give people the option to recycle their glass containers easily, either for personal use or to send to a recycling center. I can imagine someone trying to force the wick tab off the bottom and shattering the glass, cutting their hands to pieces. Quote Link to comment Share on other sites More sharing options...
burnt_fingers Posted January 7, 2010 Author Share Posted January 7, 2010 Besides Wally World, does anyone know where the 3M adhesive pads can be bought? I can go to Wally World, but it's 25 miles away. Quote Link to comment Share on other sites More sharing options...
Candybee Posted January 7, 2010 Share Posted January 7, 2010 (edited) I quit using glue dots for the same reason. Got tired of wicks coming unglued after I poured my wax. So I got a heat gun and glue sticks and they work great. If you get a glue gun make sure you get duel temp or high temp glue sticks. I use Stanley DualMelt stick or Surebonder All Purpose Stik Glue Sticks. If you use a lower melt stick you may get the wick coming unglued.I got my glue gun (a Stanley 40 Watt Glue Gun) and glue sticks at the local hardware store. The glue gun was about $20 and the sticks run about $5 or less.I have never had a wick come undone with this combo and I have been using the same glue gun and sticks for 3 years now.Plus-- you can wick your jar and pour wax into it immediately without the wait. Its not worth it to me to use something that you have to wait before you can pour wax. Edited January 7, 2010 by Candybee Quote Link to comment Share on other sites More sharing options...
inherowndominion Posted January 7, 2010 Share Posted January 7, 2010 I bought the wick stick um's from BC and I have their EZ setter and the black wick holder things (can't remember what they are called!) At first when I started using the stickums they came loose, which btw is SOOOOO FRUSTRATING, now I heat up the bottom of the jar, then use the setter and the wick holder and they NEVER come off. I can pick up the wick and the jar comes with it (16oz jj)Whether it's the heat or the other gadgets doing it, I'm not sure, I'm just happy they don't come loose anymore! I re use my test jars, so the silicone thing just wasn't an option, you gotta chisel the stuff off! Quote Link to comment Share on other sites More sharing options...
blt212 Posted January 7, 2010 Share Posted January 7, 2010 I use the wick stickers from the Candlemaker's Store and they stick really well even when pouring at higher temps (180F).....I had used others from BC, CS and others that always came loose. I preferred not to deal with the glue if I didn't have to so I was glad to find these. Someone on the forum mentioned them working well and that they also came in sheets....makes wicking go alot faster. Quote Link to comment Share on other sites More sharing options...
Candybee Posted January 7, 2010 Share Posted January 7, 2010 I pour hotter than 180 just for my parasoy candles alone. For palm I pour even hotter. Not sure a wick stickum work for me. Quote Link to comment Share on other sites More sharing options...
Jokerjen Posted January 7, 2010 Share Posted January 7, 2010 I know I have found the 3m MOUNTING TAPE at the dollar store....I had picked some up to hang stuff...but may try it... Quote Link to comment Share on other sites More sharing options...
burnt_fingers Posted January 7, 2010 Author Share Posted January 7, 2010 I just picked up a pack of the 3M Mounting Squares which is perforated so you can have 4 squares. Anyway, I am going to give it a try. The back of the package says they are a permenant fix so removing them may be a pain if removal is possibloe at all. Quote Link to comment Share on other sites More sharing options...
topofmurrayhill Posted January 7, 2010 Share Posted January 7, 2010 (edited) I just picked up a pack of the 3M Mounting Squares which is perforated so you can have 4 squares. Anyway, I am going to give it a try. The back of the package says they are a permenant fix so removing them may be a pain if removal is possibloe at all.The foam comes as squares or in a roll the same width as Scotch tape. One type of place where you can buy it is an office supplies store. Something like Staples, OfficeMax or anyplace that carries that sort of stuff.It's definitely removable. I heat the bottom of the container well with a heat gun, then pry off the wick tab with a butter knife and scrape the remaining foam off the glass. High heat does loosen it, but it's stubborn enough that I'm sure it would hold fine at palm pouring temperatures.Again, this is the same thing as wick stickums but higher performance and more consistent than what the candle suppliers sell. It will come loose when you make it do so, but I've never had it just pop off under any circumstances. Edited January 7, 2010 by topofmurrayhill Quote Link to comment Share on other sites More sharing options...
burnt_fingers Posted January 7, 2010 Author Share Posted January 7, 2010 The foam comes as squares or in a roll the same width as Scotch tape. One type of place where you can buy it is an office supplies store. Something like Staples, OfficeMax or anyplace that carries that sort of stuff.It's definitely removable. I heat the bottom of the container well with a heat gun, then pry off the wick tab with a butter knife and scrape the remaining foam off the glass. High heat does loosen it, but it's stubborn enough that I'm sure it would hold fine at palm pouring temperatures.Again, this is the same thing as wick stickums but higher performance and more consistent than what the candle suppliers sell. It will come loose when you make it do so, but I've never had it just pop off under any circumstances.You got to love those heat guns. Thanks for the info. I did not know they came in rolls. Quote Link to comment Share on other sites More sharing options...
bugtussle Posted January 8, 2010 Share Posted January 8, 2010 I use the wick stickers from the Candlemaker's Store and they stick really well even when pouring at higher temps (180F).....I had used others from BC, CS and others that always came loose. I preferred not to deal with the glue if I didn't have to so I was glad to find these. Someone on the forum mentioned them working well and that they also came in sheets....makes wicking go alot faster.We wicked over 5,000 tins and tureens this fall and never had CMs wick stickers come loose. I think some folks just like to make things tougher than they are. Carole Quote Link to comment Share on other sites More sharing options...
topofmurrayhill Posted January 8, 2010 Share Posted January 8, 2010 I did not know they came in rolls.The rolls are more economical. Squares cost 50% more per wick stick. Quote Link to comment Share on other sites More sharing options...
lsbennis Posted January 8, 2010 Share Posted January 8, 2010 We wicked over 5,000 tins and tureens this fall and never had CMs wick stickers come loose. I think some folks just like to make things tougher than they are. CaroleHave to agree with you on that one...I have used the ones from CM them for testing the last 6 months and done everything to them you can think of and not one has come loose, I'm going to start using them for all my candles since they have had a great track record with me. Quote Link to comment Share on other sites More sharing options...
radellaf Posted January 10, 2010 Share Posted January 10, 2010 I use rubber cement for testers and production. Perhaps a bit hard to apply compared to the others, but sets up in minutes and I've never had a wick "wander" at the end of a burn. Comes off extremely easily when you want to re-use the tester jars, is the best part.Main problem is that even if you apply it to both surfaces, wait, then stick (strongest bond possible), it is still not that strong a bond. Need to use something at the top to hold the wick or the tab could move right after the pour. There are stronger contact cements (like "goo") but rubber cement was what I had on hand. Quote Link to comment Share on other sites More sharing options...
Stella1952 Posted January 10, 2010 Share Posted January 10, 2010 (edited) I use rubber cement for testers and productionI don't think I'd use a volatile, hydrocarbon-based adhesive like rubber or contact cement! While both are good adhesives, I sure wouldn't use them in an application having to do with fire! Need to use something at the top to hold the wick or the tab could move right after the pourI like bowties to hold the wick straight, taut & centered, but the adhesive has to be firmly set, otherwise it will loosen. Edited January 10, 2010 by Stella1952 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.